JetCat P400PRO-GL-LN

Price excl. VAT, plus delivery

9,680.67 €
Price incl. VAT, plus delivery
Price reductions

JetCat PRO Turbines

The JetCat PRO turbines offer maximum integration and installation. All system equipment required for turbine operation is fully integrated under the turbine hood. Apart from the supply battery, the fuel tank and the control signals, no further external subsystems are required! The control signals are output on a data cable terminated with a 15-pin SUB-D connector. Power is optionally supplied via the power cable with XT60 plug for direct battery connection.

JetCat-PRO turbine functions

Integrated turbines components:

  • ECU (electronic control unit)
  • Integrated brushless fuel pump
  • Fuel and kerosene start valves
  • fuel filter
  • kerosene starter
  • Barometric height / pressure sensor
  • 4-pole Molex extension plug (e.g. for smoke pumps / fuel pump)
  • Vent opening with integrated one-way valve (e.g. for pressurizing the fuel system)

Power Supply

Over 3 cells LiPo battery / XT60 connection / capacity 3000mAh or higher

Data connector

Over 15-pin SUB-D (male) there are the following control options:

  • 1x PowerOn control signal
  • 2x PWM input channels (e.g. for RC remote control; THR / AUX)
  • 2x independent RS232 interfaces for computer remote control and / or interconnection of several turbines
  • 1x Analog voltage regulation / sensor input
  • 1x JetCat bus interface, e.g. for connection of GSU and / or other JetCat accessories (LCU / flow sensor / BMS system etc.) CAN bus interface for control and data reporting

Standard Version

The standard P300-PRO Engines have a "normal" starter motor, without generator (to save costs, e.g. for hobby applications). With our "JetCat-PRO" interface, the Engines can easily be used for RC model applications. The PRO interface has already integrated the full functionality of our telemetry adapter!

Generator Version PRO GL

These versions consist of a brushless and non-contact starter/generator system. The generator is "soft coupled", i.e. it rotates at a lower speed than the turbine shaft itself (patent pending). A built-in and integrated DC / DC converter with additional charge control enables buffering / recharging of the turbine battery. The charging system is able to supply charging energy to the Engine battery at idling speed. The electrical power of this charging system is approx. 85W. The "soft" coupling of the generator limits the power output.

Generator Version PRO GH

This version consists of a brushless and non-contact starter/generator. The generator is "hard" coupled to the turbine shaft (but there is no mechanical contact), i.e. it rotates at the same speed as the turbine. This configuration allows a much higher power output of the generator (900W!). This version is also supplied with an unregulated 3-phase alternating current supply. The three-phase voltage varies proportionally with the turbine speed. Typically, the measured no-load DC voltage is approximately 12V / 7.5A (33,000 1 / min) and 35V / 22A (100,000 1 / min) when charged with a 1.5 Ohm resistor behind a rectifier network (6x High Power Schottky diodes).

Technical Specifications

Pressure Ratio


Mass flow (kg/s)


Consumption Full load (ml/min)


Consumption Idle (ml/min)


Weight [g]


Diamter (mm)


Length (incl. Starter) (mm)


Gewicht Set im Karton (g)


Dimensions Carton (LxBxH; cm)


Exhaust Gas Temperature (°C)


Idle rpm (1/min)


Max rpm (1/min)


Thrust @ idle (N)


Thrust @ max Rpm (N)


Exhaust Gas Velocity (km/h)


Exhaust Gas Power Output (kW)


SFC @ max Rpm (kg/Nh)



Additional product information

Handbook Download


Product Note Status Price
JetCat PRO Turbines Industry Installation Set JetCat PRO Turbines Industry Installation Set
186.00 € *
JetCat PRO Turbines RC Installation Set JetCat PRO Turbines RC Installation Set
330.00 € *
JetCat P400PRO Turbinemount JetCat P400PRO Turbinemount
37.00 € *
* Prices incl. VAT, plus delivery
Display accessory details

Browse this category: Turbo Jets